2 - Acura RSX 2002-2006

Chromoly Spring Base w/ .440"" ID Spring Step - Use on K Series Engines Originally Equipped w/ Single Valve Springs

IN: 0.531"" / 266@1mm; EX: 0.492"" / 262@1mm

IN: 0.580"" / 275@1mm; EX: 0.565"" / 277@1mm - 3 Lobe Forged Tool Steel Core

Invidia Exhaust delivers high quality systems for your car. For better performance and sound!

Set of 16

IN: 0.551"" / 276@1mm; EX: 0.512"" / 282@1mm

Allows Installation of RBC Pattern K Throttle Body to a Manifold Using Early Ford 5.0L Bolt Pattern - 72mm on K Series Side

Upper And Lower Hose Only - 1.25"" Diameter

Completes One Mounting Point - Includes Two Red Polyurethane Bushing Halves - Used to Replace the Bushing in Rear Camber Kits and Pro Series Rear LCA

Exhaust Gear Only.

Dish Face - Intake: 35mm x 108.85mm x 5.48mm; Exhaust: 29mm x 108.85mm x 5.45mm - PVD Chromium Nitride Coated

Seat Pressure: 100 lbs at 1.600” - Open Pressure: 255 lbs at 1.100” - Coil Bind: .890” - Max Lift: .680” Must Use Skunk2 PN 312-05-0010 (Spring Bases) to Install Dual Springs in Single Spring K Series Heads or Install K Valve Springs in F20C/F22C Engines

Ultra Race Center Feed Plenum - 5.0L Volume - 90mm Inlet, 5.0 Ford T/ Body Bolt Pattern (4.25"" Square Bolt Spacing)

These mounts are made out of high grade billet aluminum material and steel. The mounts feature 70 durometer bushings which keep vibrations down to a minimum while keep your engine in place under hard acceleration, cornering, and braking.

Titainium - 42% Lighter than OEM Steel Retainers - 7° Keeper Seat - Pair with Alpha Series or Pro Series Valve Springs - Must Use Skunk2 P/N 312-05-0010 on 2005+ K Series Engines

Direct Replacement For OEM Intake Manifold Gasket

+/- 3.3 Degrees - Includes Polyurethane Bushings

High performance radiators from Japanese Koyorad for those with high requirements from their cooling system

Style your ride with some fresh lighting. Spyder Auto offers both headlights, taillights, indicators and more. Awesome quality to affordable prices.

Allows Installation of RBC Pattern K Throttle Body to a Manifold Using Honda PRB Bolt Pattern - 72mm on K Series Side

K&N Typhoon® air intake systems are built for performance and show. This free-flowing mandrel-bent aluminum tube induction system was designed to fit many sport compact performance vehicles. Typhoon air intakes come with a high-flow conical air filter designed to provide increased surface area and dust capacity. Some Typhoon air intakes are not legal for use in California and other states adopting California emission standards while others are CARB exempt and 50 state legal. Check the K&N air intake product page for specific CARB status.

These mounts are made out of high grade billet aluminum material and steel. The mounts feature 70 durometer bushings which keep vibrations down to a minimum while keep your engine in place under hard acceleration, cornering, and braking.

IN: 0.620"" / 284@1mm; EX: 0.580"" / 284@1mm - 1 Lobe Forged Tool Steel Core

Direct Replacement or Oversize Throttle Body Gasket.

Hard Anodized - Polyurethane Bushings - Includes Special Socket for OEM Bolt Removal

92-Up B Series - Fits Over OEM Solenoid - Skunk2 Inside

DW65C series, 265lph compact fuel pump without mounting clips w /install kit for RSX 02-06,Civic 01-05, MX5 2006-2015

Clear - Ultra Race 1.0 Liter Plenum Spacer - Includes Gaskets

5.472 length for 22mm/.866 wrist pin diam

Provides power gains while maintaining A/F ratios with no additional tuning